| 1. | Process the film and label each frame as to the number of turns .
冲洗胶卷，并在每张照片上标明转动的圈数。 |
| 2. | The number of turns of wire in the secondary coil is the same as the number of turns in the primary .
次级线圈的圈数和初线线圈圈数一样。 |
| 3. | Number of turns to create one peasant or knight
创造一个农民或者骑士所需要的回合数 |
| 4. | Meter for counting number of turns
匝数计量器 |
| 5. | It reduces the number of particles and other settings to insure that at least a certain number of turns are calculated every second
它可以减少显示的粒子束、改变各种设定，使每秒钟模拟的圈数至少达到一个确定的值。 |
| 6. | A measure of the induced voltage in a circuit caused by a magnetic flux and equal to the flux times the number of turns in the coil that surrounds it
碰撞，匝链电路中由于磁通量而造成电伏减少的单位，等于穿过一载流线圈的磁通量与线圈匝数之积 |
| 7. | Find the total range of your compression adjusters by turning them out to the full soft position , then , counting the number of turns or clicks , turn them in until they stop
找出你车压缩阻尼调节器的范围，转动到最软的位置，然后回转到不能转动为止，计算转动的圈数或滴答声，这就是调节的范围。 |
| 8. | 4 . to get the motor ' s performance by calculation with known formulas , as a result an adjustment for the motor ' s configuration can be practised . when a combined method of altering the length of armature , the number of turns in the winding and the dimension of permanent magnet is used . 5 . to get the motor ' s performance when it is driven by the power converter . finally , the calculated data are compared with the experimental measurements , so as to verify the rationality and reliability of the method
Q采用数值分析直轴负载磁场和交轴电枢反应磁场的方法来计算，得到较为准确的结果；根据电机工作特性的计算公式计算电机性能，由计算结果调整电机的结构，而调整工作使用改变电机铁心长度、绕组匝数和永磁体尺寸相结合的方法，这样可以得到较为理想的结果；对变频电源供电时电机的工作特性进行计算，以检验其变频时的性能。 |
| 9. | Abstract : a method named multi - times optimization is presented to solve the multi - specification optimization problem , which is difficult to solve using the variational optimal theory . in the method several demands are reduced to some sub - tasks . in every subtask a demand that can not be transformed into bound condition is taken as performance specification for optimazation , and the other demands are taken as bound conditions . by means of the method , the arrival time , number of turn , turn angle of the aircraft in the terminal area are selected as performance specification separately , and the general character of optimal flight route in the terminal area is given
文摘:为了给飞机提供一条能满足多种指标要求的最优飞行轨迹，针对变分最优理论难以求解多指标优化问题，提出了命名为多次优化的方法，即将多要求的优化任务分成先后相继的多次任务，每次任务中选取一种不能边界转化的要求作为最优性能指标，而其余要求转化为边界条件.利用这一方法以时间、转弯次数、转弯角度为最优性能指标给出了终端区最优飞行轨迹的一般特征 |
